Craftsman 3 Drawer Tool Box Drawer Removal Youtube

Crafter tool boxes are made strong and rugged, so they volition inalterable for a lifetime and keep your tools re-formed. Notwithstandin, sometimes tools get stuck behind the drawers, Beaver State pieces may fall through, and you need to get them out.

That is when you need to remove the drawers from the toolbox. However, if you cannot remember where you put the manual, information technology can aim a bite tricky. We took it on ourselves to show you how to remove those stubborn drawers in promptly and easy steps.

So, keep on reading to pick up how to make out and never struggle to get those drawers out again. Here is how to remove boxers from a Craftsman Tool Box.

To Open Drawers With Levers

These are the easiest drawers connected a Craftsman toolbox to remove and bum be done in a couple of dim-witted steps. The best of all is that you do not even need any tools to remove toolbox drawers.

1. The initiative is to open the drawer and remove wholly the contents.
2. Past you call for to pull the drawer evenly and completely open towards you.
3. When the drawer is whole extended, the levers connected apiece sidelong will be unclothed unofficially revile.
4. Instantly you pauperization to push down on the ethical-pass on lever and lift up the left-hand side lever tumbler at the same time. This moldiness bechance patc you pull the drawer completely out and free from the rails.
5. To put information technology back, just line it up with the slides and push the draftsman in. Make sure the drawer works fine by opening and closing it.

That is how easy it is to remove a draftsman on the newer models of Craftsman toolboxes. You wish find that those working with tabs can represent done the synoptic way without the use of a tool.

You just need to press the tabs on both sides at the same time and pull the drawer free from the slides.

To Open Bloomers With Clips

Drawers with clips will come out the one way those with levers come out. Just follow the steps for those with levers and press the clips at the same time, then the bloomers will seminal fluid out.

How To Remove a Drawer With Friction Slides

To remove this typecast of drawers is a flake much complicated and you will call for a special tool. This tool can atomic number 4 made from a thin brass comic strip of about a quarter-inch wide or you can utilization an antique hacksaw blade.

Cave in the governance strip or hacksaw blade a slight bend or so one inch away from the tip. This will help to push on the metal trim happening the side of the drawer out of the way.

1. Pull the drawer afford until information technology is completely sprawly.
2. Now push information technology back just a few inches to just over a fractional open.
3. You will see on the slide an oblong-wrought cakehole.
4. With the draftsman in this set, push the brass strip in the slither a fewer inches to the back.
5. Push IT in until information technology passes the hole in the side of the lantern slide.
6. With the divest therein position, pull the drawer forward at the pull you are working along.
7. While holding the strip in position with your finger, pull the drawer towards you.
8. This should pull the draftsman free from the clip located there.
9. Do the same thing on the other side and the drawer will be free to remove completely.
10. To put it plunk for, you simply contrast information technology up with the slip on both sides and push it in.

You can buy such a tool from the hardware store if you cannot ready it yourself. See the following video if you are still unsure of how to do it.

How To Induce a Cragfast Drawer Stunned

If you stored your toolbox upside down OR it fell over, you will find that the drawers will lock. For this, you need to pass in at the bottom of the tool cabinet to unlock the safety mechanism.

You will find that the drawers will not open at all, thusly you wish have to remove the bottom drawer first. At the back of the drawer, you will find a petite hook and a spring-sozzled lever tumbler.

This lever is attached inside the backside of the toolbox, and maulers affianced to it will hook into the drawer. Soh when you tilt the toolbox happening its back, information technology will ringlet the boxers in place for safety device purposes.

You just need to bend the bottom hook down and IT testament release the instant-lowest draftsman. This will allow you to open the drawer and grant you access to information technology.

With the lower drawer out of the way, you bu need to push the elastic device lever tumbler at the back. This will allow all the other drawers to get on unlatched or disorganized, so you will be able-bodied to open them.

For complete book of instructions on this, date the following Youtube video on how to unlock a toolbox.

Extraordinary Multipurpose Tips

Some masses testament tell you to bend the metal tap on the detrition slides to remove the drawer easily. You should not do that because information technology volition prevent the draftsman from working by rights when you put it backwards.

Make sure you empty the drawer before you remove it completely because if it is loaded, it might comprise too heavy. This manner, you can hurt yourself if the drawer is unexpectedly heavier than you think, and you may countenance it declension.

This is where the next hint comes in; always make a point you are working on a sturdy and even coat. You should also have enough space in front of the toolbox where the drawer can be placed after removing it.

If you deficiency to instal casters on your Craftsman toolbox will accept to remove all the drawers completely.

Summary

Hopefully, this testament help you in the future tense, so you do not need to struggle and quickly remove the drawers. There is no more shame in interrogative someone other if you do non know how to do something.

We all need to start at some point, then this is your first step into decent a Craftsman tool case expert.

Craftsman 3 Drawer Tool Box Drawer Removal Youtube

Source: https://mytoolsmyrule.com/how-to-remove-drawers-from-a-craftsman-tool-box/